Learning CenterWhat is a mineral?The most common minerals on earthInformation for EducatorsMindat ArticlesThe ElementsThe Rock H. Currier Digital LibraryGeologic Time
搜索矿物的性质搜索矿物的化学Advanced Locality Search随意显示任何一 种矿物Random Locality使用minID搜索邻近产地Search Articles搜索词汇表更多搜索选项
╳Discussions
💬 Home🔎 Search📅 LatestGroups
EducationOpen discussion area.Fakes & FraudsOpen discussion area.Field CollectingOpen discussion area.FossilsOpen discussion area.Gems and GemologyOpen discussion area.GeneralOpen discussion area.How to ContributeOpen discussion area.Identity HelpOpen discussion area.Improving Mindat.orgOpen discussion area.LocalitiesOpen discussion area.Lost and Stolen SpecimensOpen discussion area.MarketplaceOpen discussion area.MeteoritesOpen discussion area.Mindat ProductsOpen discussion area.Mineral ExchangesOpen discussion area.Mineral PhotographyOpen discussion area.Mineral ShowsOpen discussion area.Mineralogical ClassificationOpen discussion area.Mineralogy CourseOpen discussion area.MineralsOpen discussion area.Minerals and MuseumsOpen discussion area.PhotosOpen discussion area.Techniques for CollectorsOpen discussion area.The Rock H. Currier Digital LibraryOpen discussion area.UV MineralsOpen discussion area.Recent Images in Discussions
Techniques for CollectorsTrimming specimens
27th Aug 2018 15:53 UTCGreg Simmons
As an example prompting the question, I have three Herkimer specimens in matrix... a LOT of matrix. I'd really like to trim them back quite a bit so they a) don't take up so much space in my cabinet, and b) don't weigh as much on the shelf.. it's only glass.
Pretty much what I have is a rock pick and a cold chisel. I do have a rotary tool too but question if any of the attachments would work on rock.
Thanks in advance everyone!
27th Aug 2018 16:06 UTCDon Saathoff Expert
We use a homemade splitter, a trim saw, horse hoof trimmers (flea market), tile trimmers, hammer & chisel, etc. Practice will teach what works on the matrix at hand....
Don
27th Aug 2018 16:19 UTCDavid Von Bargen Manager
I wouldn't use a hammer and chisel on any specimen that would be rated as fair. You stand a pretty high chance of the rock not breaking the way you want it to and also popping off of any good crystals on the specimen. That method gives you almost no control on how the rock would break.
For small specimens (<1" or so), you can use tile nippers to reduce the matrix. Up to maybe 3" or so, you can use one of the screw type trimmers. For serious breaking, you step up to a hydraulic trimmer. The "professional" trimmers allow you to accurately put stress on the rock where you want it to break (this doesn't always work though).
These types of trimmers allow you to place a strain on the rock where you want to break the rock. They also usually have guards to protect you from flying rock chips and also keep the broken pieces in a known area.
27th Aug 2018 18:26 UTCDoug Schonewald
27th Aug 2018 18:36 UTCAlfredo Petrov Manager
27th Aug 2018 18:49 UTCSusan Robinson
27th Aug 2018 19:16 UTCHorst Schabereiter
Horst
27th Aug 2018 19:35 UTCEd Clopton 🌟 Expert
For a vug of crystals that can be easily washed out, filling the vug with thin mud helps absorb the shock of trimming the matrix by keeping free-standing crystals from "waving" and snapping off as shock waves reach them.
I don't know whether it's my imagination or whether it really works, but the effects of striking and breaking hard limestone and dolostone sometimes seem less (as in knocking crystals off the matrix some distance away from the trim) when the rock is wet. Maybe the water filling in the pores of the rock helps to absorb some of the shock.
For very small pieces (thumbnails and micromounts) I use a pair of cheap wire cutters. I bought them to use up on rocks, but they are still sharp enough to cut wire after 20+ years of off-and-on (ab)use.
To Alfredo's list of challenging rocks to trim I will add granite pegmatite. Fine-grained granite may be fairly homogeneous and inclined to break in a predictable direction, but the large crystal boundaries and cleavage planes that come with the coarser texture make trimming something on pegmatite matrix a real challenge and gamble.
After 30+ years of active collecting, I have evolved a keen sense of when I have just gone one whack too far and ruined something! (Still working on sensing when I'm about to take that last whack . . .)
27th Aug 2018 22:31 UTCGreg Simmons
28th Aug 2018 08:56 UTCUwe Kolitsch Manager
28th Aug 2018 13:11 UTCKeith Compton 🌟 Manager
Don't know if they have stopped but the following supplier - Mikon Mineralienkontor - (advertises on Mindat) and has the Zuber trimmers and spare chisels listed as being available
https://www.mikon-online.com/
Cheers
28th Aug 2018 14:28 UTCHarold Moritz 🌟 Expert
https://absoluteclarity.com/collectors/precision-splitters/
But for very large/tough matrix a hydraulic trimmer is needed. You may need one for the tough Little Falls dolostone found in the Herkimer area (I feel your pain). These are large and expensive, but you may be able to rent one instead. One advantage of these is that there is not torque, you pump the chisel tips together with a lever. They are marketed for splitting granite pavers, etc.
When doing any splitting, always start as far away from the area you want to keep as possible and work incrementally toward it. Splits have a tendency to "short-circuit" to the closest surface or open space in the rock rather than propagate through across, so start conservatively. Then after removing some matrix, the remaining piece becomes progressively easier to split and your control over where the split goes gets better.
One thing to remember when doing this is that the chisel tips need to be set against two matrix surfaces that are more or less parallel. Little natural notches or bumps in the surface will help hold them. If not, then as pressure is applied the chisel tips will either slide along a face rather than cut into it, or the piece will slip out. When a piece is rather tetrahedral in shape it can be difficult to split. So try cutting some small flat surfaces into the matrix where the chisels can be "set".
As mentioned above, practice. Take some dolostone with empty vugs and pretend there is a good crystal in there you want to save and have at it.
28th Aug 2018 14:53 UTCBob Harman
28th Aug 2018 16:22 UTCHolger Hartmaier 🌟
Speaking from personal experience, be extremely cautious when considering trimming Herkimer crystal matrix specimens. The crystals are usually attached by a thin film of hydrocarbon material only and will not tolerate too much shock. Lots of good advice in the previous posts.
Also, it is worth noting that rocks are very weak in tension. The tensile strength is typically about 1/10 of the compressive strength. When loading a rock in compression in a vise or trimmer, the crack is propagated due to tensile forces acting at 90 degrees to the direction of loading. Naturally occurring planes of weakness, such as cleavage, bedding, foliation, fractures should be exploited first to remove excess material because there is some predictability where the rock is likely to break. Banging away on an otherwise solid-looking piece of matrix requires more energy to generate a fracture, with potential for unintended consequences.
As noted in previous posts, experiment with waste rocks of similar material. Don't load the trimmer to much or too rapidly. Gradual loading until you hear the first crack may be enough to allow removal of loosened material by hand, under controlled conditions. Building up a lot of strain will result in a more explosive, uncontrolled failure. Consider enclosing or wrapping the specimen in a bag to contain all the pieces and to prevent further damage to fragments when they fly around.
Good luck!
Holger
28th Aug 2018 17:53 UTCGreg Simmons
28th Aug 2018 18:10 UTCBeth Heesacker
Last I heard he was waiting for everything to arrive and then tool up to build them.
My go-to trimmer for the large or hard material is a hydraulic bearing pusher from Harbor Freight equipped with knives. My hubby and my son are handy at wire welding.
I do not find it on Harbor Freight anymore but it looks somewhat like the one Bob pictured.
28th Aug 2018 22:51 UTCJohn Oostenryk
It has been discontinued for a couple years now. At half the price of a Zuber-I'd say it was a good deal! I got mine NIB for $600 about 5 years ago. Would re-buy same in a heartbeat!!
*He is mistaken-he did not have that made in a machine shop. IN a prior post- he said he borrowed it from a friend, ...https://www.mindat.org/mesg-19-291726.html
Must have changed the springs to a thicker coil - hence it will not close far enough to touch cutters together. (coils take up too much space.)
Mine is stock and definitely will close fully!
I have the exact same model- it is a wonderful workhorse! purchased in 2013
This is their 'newer model' with the springs captured around the lower connecting rod.
Note also the bolts that hold the brass sleeved guides for upper plate(slide bearing surface).
I have made thousands of trims so far... majority sedimentary strata. All good.
Occasionally needs a lil tightening of connectors, the jack is starting to bypass some pressure but no bigge
The earlier units did not have the removable guides(not easily-anyway-welded on) AND the springs were external, hanging from hooks. I use a model as such in the prep lab at my college. Works fine- but do run a piece of steel cable through the (external)springs to capture them, in case a hook should fail. not as bad as the old school garage door springs but same problem-flying off... ;)-
I commented on this prior: https://www.mindat.org/mesg-19-292033.html
ALSO:
https://www.swarfsystems.com/products Got some nice stuff- I have been meaning to purchase a new set of cutters from them!
Check out the Harbor Freight kit he offers.
https://www.midcornwallminerals.co.uk/cornish-mineral-sales/cornish-rock-trimmers/ I have spoke with him about his small trimmer units. Good Stuff!
Further threads on Mindat:
https://www.mindat.org/forum.php?read,19,49028,424680 More trimmer details
https://www.mindat.org/mesg-19-356256.html Lots about using grinder+diamond blade for trimming.
There are a few others too...
Overall--
YMMV?!
Good luck and have fun!
28th Aug 2018 23:58 UTCBob Harman
29th Aug 2018 00:46 UTCBrian Gray
29th Aug 2018 03:40 UTCRobert Rothenberg
Bob
29th Aug 2018 10:09 UTCPeter Nancarrow 🌟 Expert
- and in response to Bob's comment above, one of the things I have used it for is obliterating unsightly saw cut surfaces!
Pete N.
29th Aug 2018 20:24 UTCGreg Simmons
You guys ROCK!
:-)
版权所有© mindat.org1993年至2024年,除了规定的地方。 Mindat.org全赖于全球数千个以上成员和支持者们的参与。
隐私政策 - 条款和条款细则 - 联络我们 - Report a bug/vulnerability Current server date and time: 2024.5.6 01:56:52
隐私政策 - 条款和条款细则 - 联络我们 - Report a bug/vulnerability Current server date and time: 2024.5.6 01:56:52